Search Menu
Photonics Media Photonics Buyers' Guide Photonics EDU Photonics Spectra BioPhotonics EuroPhotonics Vision Spectra Photonics Showcase Photonics ProdSpec Photonics Handbook
More News

Building a Better — But Still Tiny — Sensor

Facebook Twitter LinkedIn Email Comments
DNA aptamers improve sensing ability of atomic force microscopy

Hank Hogan

For an atomic force microscope, familiarity can breed better images — in more ways than one. When the microscope’s tip has a sensing molecule tethered to it, the molecule enables the device to recognize targets in the sample being scanned. That chemical familiarity also enables the microscope to perform biological imaging of complex samples in water, something it could not accomplish otherwise.

The standard choice for a sensing molecule has been an antibody, which helps pick out proteins for which it has an affinity. Now a group from Arizona State University in Tempe has used DNA aptamers — manufactured single-stranded DNA molecules. Stuart Lindsay, a professor of physics and chemistry and leader of the research team, noted that aptamers offer a significant advantage over the typical antibody approach because their chemistry is simpler. “The simpler chemistry seems to make everything work better,” he said. “Better signal to noise, for example.”

A schematic, not to scale, shows an atomic force microscope probe with attached aptamer scanning a surface. Because of its structure and chemistry, the aptamer alters the probe’s response near particular molecules, enabling the location of that type to be mapped. Image courtesy of Stuart Lindsay, Arizona State University.

In atomic force microscopy, a stylus with a very sharp point is brought close to a sample surface. The tip is mounted on the end of a cantilever, and the interaction between the tip and the sample deflects the cantilever. That deflection is amplified by an optical lever in which a laser is fired at the cantilever and bounces off it; the reflected beam is detected by a photodiode. Because the lever arms are long, they magnify the deflection by a factor of thousands or more, making it possible to spot small movements and achieve molecular-scale imaging.

For biomolecular imaging, one of the biggest problems with this technique is that it is nearly impossible to distinguish between proteins, even if their molecular weight is very different, based on a topographical image alone. So researchers have attached sensor molecules, such as antibodies, to the tip of the stylus and bounced the probe up and down slightly. As the tip moves across the surface, the oscillation changes when the sensor binds to a target on the surface. This information is used to locate the target proteins.

The scheme is promising, but the investigators note that one issue is the high surface concentration under the probe. Consequently, the chemical recognition signal may appear even if the affinity between the antibody and a molecule is small. The result is noise that can mask the true signal.

In contrast to antibodies, which are natural, aptamers are man-made. Starting with a random sequence of DNA or RNA, they are created through a process called systematic evolution of ligands by exponential enrichment. Aptamers can recognize specific ligands and bind to nucleic acids, proteins or small organic compounds. Because they consist of a single DNA strand, they are easy to synthesize and store, and they are easily attached to the microscope’s probe tip.

Aptamers also have a high affinity for some small molecules, which might allow recognition imaging of minor chemical changes, such as elements of an epigenetic code, information in addition to that encoded in the DNA. “My own goal is to map epigenetic markings at the molecular level,” Lindsay said.

For a demonstration of their approach, which was published in the June issue of Biophysical Journal, the scientists chose the aptamer that binds to human immunoglobin E (IgE). They did so primarily because this aptamer produces significant adhesion in atomic force microscopy force curves.

Immunoglobin E (IgE) was imaged with a DNA aptamer, a recognition molecule shown in green and tethered to an atomic force microscope probe via a polyethylene glycol linker, shown in red (a). The technique enables the depiction of the topography of the IgE molecules on a mica substrate (b) as well as simultaneous acquisition of recognition signals derived from the aptamer’s interaction with IgE (c). Adding a solution of IgE blocked further signals (d). Traces (between the green arrows) are shown for the topography (e) and recognition (f) steps.

They functionalized the probes with an ethylene-glycol oligomer, leaving a thiol-reactive maleimide at the end of the molecule to act as a tether for the aptamer. Because of the tether length, the resulting resolution was ∋5 nm. They used an atomic force microscope from Tempe-based Molecular Imaging Corp., now part of Agilent Technologies Inc.

The researchers coated a mica substrate with a solution containing IgE. After some additional processing, they imaged the substrate at a scanning speed of about 2 μm/s and with an oscillation amplitude of ∋5 nm. They found that nine out of 10 features on the surface of the right size to be IgE molecules were picked up by the aptamer sensor, a recognition efficiency of 90 percent. Moreover, there was a clear difference between the background signal and that of a legitimate spot, indicating a higher signal-to-noise ratio than is typically achieved by antibody-based sensors.

The investigators demonstrated that the effect was specific. When IgE molecules were injected into the solution, the recognition signal disappeared because it was blocked. When they imaged surfaces coated with another protein, thrombin, there were no recognition events. Also, when they imaged a surface coated with a mixture of thrombin and IgE, the recognition events tracked to a degree the molar ratio of the mixture. The actual ratio of molecular recognition was higher than the molar ratio, a difference that could have resulted from preferential surface adsorption of the IgE.

The improved signal-to-noise ratio of the aptamer approach as compared with one based on antibodies was not due to stronger binding. Tests showed that the force required to break the aptamer bonds was actually somewhat smaller than the force required to break the antibody bonds. However, other tests have shown a similarly small difference, but with the aptamer bond slightly stronger than the antibody one.

In applying the technique, it would be necessary to have the appropriate aptamers, with the molecules designed to bind to a given target, Lindsey noted. Therefore, work must be done developing and producing the aptamers. That can be a challenge, but the researchers are working on it.

“We are building an aptamer factory, but it’s not easy. On the other hand, if we get things working, we’ll avoid the batch-to-batch variation that plagues natural products like antibodies,” Lindsay said.

Jul 2006
Basic ScienceBiophotonicsindustrialMicroscopyResearch & TechnologySensors & Detectors

back to top
Facebook Twitter Instagram LinkedIn YouTube RSS
©2019 Photonics Media, 100 West St., Pittsfield, MA, 01201 USA,

Photonics Media, Laurin Publishing
x Subscribe to BioPhotonics magazine - FREE!
We use cookies to improve user experience and analyze our website traffic as stated in our Privacy Policy. By using this website, you agree to the use of cookies unless you have disabled them.