Search Menu
Photonics Media Photonics Buyers' Guide Photonics Spectra BioPhotonics EuroPhotonics Vision Spectra Photonics Showcase Photonics ProdSpec Photonics Handbook
More News

Dissolving CIGS for flexible application

Facebook Twitter LinkedIn Email Comments
Anne L. Fischer, Senior Editor,

Solar cell designs traditionally are based on crystalline silicon, but not only has that material been in short supply, the silicon-solar process is relatively expensive. And as the solar industry strives to decrease the cost to make it a viable alternative to fossil fuels, many are turning an eye toward panels with copper indium gallium selenide (CIGS) as an alternative.

Although CIGS cells have proved efficient and have the potential to cost less, a low-cost production method has eluded the industry. Researchers at Henry Samueli School of Engineering and Applied Science at the University of California, Los Angeles (UCLA), are aiming to change that by developing a low-cost production method for solar cells based on CIGS.

The group, led by Yang Yang, a professor in the department of materials science and engineering, recently published a study in the journal Thin Solid Films that describes a low-cost method for manufacturing on a large scale. The study reports the efficiency at 7.5 percent, but the team has surpassed that, improving to 9.3 percent.

The dissolution method

Key to the method is the fact that it does not use a vacuum evaporation process. Most CIGS solar cells are produced by heating each of the active elements and depositing them onto a surface in a vacuum. This “co-evaporation” method can be costly and time-consuming, Yang said. Instead, the investigators dissolved the materials into a liquid, applied it onto a substrate and baked it. They had been dissolving organic materials for both LED and solar cell applications, and it was only recently that they applied this concept to inorganic materials such as CIGS.

Doctoral candidate William Hou works with the UCLA team that is developing a low-cost production method for CIGS solar cells.

They used hydrazine to dissolve the copper sulfide and indium selenide to form the constituents for the copper indium sulfur selenide. According to Yang, they also can dissolve gallium, but they left if out to simplify the material system for research purposes. He also said gallium may be replaced by sulfur because of cost, adding that gallium costs 500 times more than sulfur.

Not only did they find their method of liquefying the materials cheaper and easier than the vacuum method, but the materials can be applied to various surfaces, including film that can be manufactured in a roll-to-roll process.

Yang said that, even though the material system is unchanged, “the quality of the material is very different between the conventional methods and our process.” The challenges have been in understanding the type of defects that result from the solution-processing method “and to either eliminate or passivate the defects.”

As far as efficiency goes, he said they are seeing an increase of about 1 percent every two months and expect to reach 15 to 20 percent within a few years. Currently, the best CIGS method achieves about 20 percent but is more costly and challenging to produce and cannot be applied to the range of surfaces that the new UCLA method can.

A flexible future

The significance of this work is the potential of using a flexible insulating material such as polyimide, which cannot tolerate the traditional method of processing CIGS. “Most demonstrations of flexible CIGS solar cells are done on metal foils,” Yang explained, adding that “this creates various problems.” The low-temperature process offers a way to fabricate CIGS on polyimide without serious degradation, he said.

Yang expects to see commercial products based on this method in three or four years.

Photonics Spectra
Sep 2009
Anne L. FischerCIGSCopper sulfideCrystalline SiliconenergyFischergalliumGreenLightIndium selenideindustrialpolymidesolar cellssulphurThin Solid FilmsUCLAVacuum methodYang YangLEDs

back to top
Facebook Twitter Instagram LinkedIn YouTube RSS
©2019 Photonics Media, 100 West St., Pittsfield, MA, 01201 USA,

Photonics Media, Laurin Publishing
x Subscribe to Photonics Spectra magazine - FREE!
We use cookies to improve user experience and analyze our website traffic as stated in our Privacy Policy. By using this website, you agree to the use of cookies unless you have disabled them.