Search Menu
Photonics Media Photonics Buyers' Guide Photonics EDU Photonics Spectra BioPhotonics EuroPhotonics Industrial Photonics Photonics Showcase Photonics ProdSpec Photonics Handbook
More News
Email Facebook Twitter Google+ LinkedIn Comments

Light Emitting Diodes - A Primer
Sep 2008
Russ Dahl, Opto Diode Corporation

From the Web Exclusive, "Seeing the True Colors of LEDs."

Light emitting diodes (LEDs) are semiconductors that convert electrical energy into light energy.  The color of the emitted light depends on the semiconductor material and composition.  The LEDs are generally classified into three wavelengths:  Ultraviolet, visible and infrared.

The wavelength range of commercially available LEDs with single-pixel-output power of at least 5mW is 360nm to 950nm.  Each wavelength range is made from a specific semiconductor material family, regardless of the manufacturer. 

Ultraviolet LEDs (UV LEDs):  320nm - 360nm

UV LEDs are rapidly becoming commercialized, specifically used for industrial curing applications and medical/biomedical uses.  Until recently, the lower wavelength limitation for high-efficiency die was at 390nm.  It has been moved to 360nm and further developments over the next few years will likely see the commercialization of high efficiency die in the 320nm region. 

The material primarily used for UV LED’s is gallium nitride/aluminum gallium nitride (GaN/AlGaN).  At this time the technology does not yield high power LED’s and the market is unsettled as several companies are moving to improve their processes.

Near UV to Green LEDs:  395nm - 530nm

The material for this wavelength range of products is indium gallium nitride (InGaN).  It is technically possible to make a wavelength anywhere between 395nm and 530nm.  However, most large suppliers concentrate on creating blue (450nm- 475nm) LEDs  for making white light with phosphors and green LEDs that fall into the 520nm - 530nm range for traffic signal green lighting. 
Rapid advancements and improvements in efficiency are noted in the blue wavelength range, especially, as the race to create brighter and brighter, white illumination sources continues.

Yellow-Green to Red LEDs:  565nm - 645nm

Aluminum indium gallium phosphide (AlInGaP) is the semiconductor material used for this wavelength range.  It is predominately used for traffic signal yellow (590nm) and red (625nm) lighting.  The lime green (or yellowish-green 565nm) and orange (605nm) are also available from this technology, but they are somewhat limited.  The technology is rapidly advancing on the red wavelength in particular because of the growing commercial interest in making red-green-blue white lights. 

It is interesting to note that neither the InGaN or AlInGaP technologies are available as a pure green (555nm) emitter.  Older, less efficient technologies do exist in this pure green region, but they are not considered efficient or bright.  This is due largely to a lack of interest and/or demand from the market place and therefore a lack of funding to develop alternative material technologies for this wavelength region.

Deep Red to Near Infrared (IRLEDs):  660nm - 900nm

There are many variations on device structure in this region, but all use a form of Aluminum Gallium Arsenide (AlGaAs) or Gallium Arsenide (GaAs) materials.  There is still a push to increase the efficiency of these devices, but the increases are only incremental improvements.  Applications include infrared (IR) remote controls, night vision illumination, industrial photocontrols and various medical applications (at 660nm - 680nm).

Theory of LED Operation

LEDs are semiconductor diodes that emit light when an electrical current is applied in the forward direction of the device.  An electrical voltage that is large enough for the electrons to move across the depletion region and combine with a hole on the other side to create an electron-hole pair must be applied.  As this occurs, the electron releases its energy in the form of light and the result is an emitted photon. 

The bandgap of the semiconductor determines the wavelength of emitted light.  Shorter wavelengths equal greater energy and therefore higher bandgap materials emit shorter wavelengths.  Higher bandgap materials also require higher voltages for conduction.  Short wavelength UV-Blue LED’s have a forward voltage of 3.5 volts while near-IR LEDs have a forward voltage of 1.5 - 2.0 volts.

Wavelength Availability and Efficiency Considerations

High efficiency LEDs can be produced in any wavelength range, with one exception - the 535nm to 560nm range. The overriding factor as to whether or not a specific wavelength is commercially available has to do with market potential, demand, and industry-standard wavelengths.  This is particularly pronounced in the 420nm - 460nm, 480nm - 520nm, and the 680nm - 800nm regions.  Because there are no high-volume applications for these wavelength ranges, there are no high-volume manufacturers providing LED products for these ranges.  It is possible, though, to find medium and/or small suppliers offering products to fill these particular wavelengths on a custom basis. 

Each material technology has a spot within the wavelength range where it is most efficient.  This point is very close to the middle of each range.  As the doping level of the semiconductor increases or decreases from the optimal amount, efficiency suffers.  That is why a blue LED has much greater output than green or near UV, amber has more than yellow-green, and near IR is better than 660nm.  When given a choice, it is much better to design for the center of the range than at the edges.  It is also easier to procure products if you are not operating at the edges of the material technology.

Supplying current and voltage to LEDs

While LEDs are semiconductors and need a minimum voltage to operate, they are still diodes and need to be operated in a current mode.  There are two main ways to operate LEDs in DC mode.  The easiest and most common is using a current limiting resistor (See Fig. 1). The disadvantage to this method is the high heat and power dissipation in the resistor.  In order for the current to be stable over temperature changes and from device-to-device, the supply voltage should be much greater than the forward voltage of the LED.

In applications where the operating temperature range is narrowWeb.Ex.Fig1.jpg (less than 30°C) or the output of the LED is not critical, a simple circuit utilizing a current limiting resistor may be used as shown here:

Fig. 1 - The current value is found by applying the equation I=(Vcc-Vf)/RL. To be absolutely certain of the current flow in the circuit, each LED VF would have to be measured and the appropriate load resistor specified. In practical commercial applications Vcc is designed to be much larger than VF and thus the small changes in VF do not affect the overall current by a large amount. The negative aspect of this circuit is a large power loss through RL.

A better way to drive the LED is with a constant current source (See Fig. 2).  This circuit will provide the same current from device-to-device and over temperature shifts.  It also has lower power dissipation than using a simple current limiting resistor.
Fig. 2 - An example of an accurate and stable circuit. This circuit is commonly referred to as a constant current source. Note that the supply current is determined by the supply voltage (Vcc) minus Vin divided by R1, (Vcc-Vin)/R1.

Commercial, off-the-shelf LED drivers are available from a number of different sources.  Typically these operate using pulse width modulation (PWM) principles for brightness control. 


Fig. 3. -  Gardasoft Vision’s PP500 Series LED Lighting Controller

Pulsing LEDs in high current and/or high voltage mode for arrays in series-parallel configuration creates a unique set of problems.  For the novice designer it is not practical to design a current-controlled pulse drive with the capability to deliver 5 amps and 20 volts.  There are a few manufacturers of specialty equipment for pulsing LEDs (See Fig. 3), such as Gardasoft Vision ( 

For more information, visit: Seeing the True Colors of LEDs

The technology of generating and harnessing light and other forms of radiant energy whose quantum unit is the photon. The science includes light emission, transmission, deflection, amplification and detection by optical components and instruments, lasers and other light sources, fiber optics, electro-optical instrumentation, related hardware and electronics, and sophisticated systems. The range of applications of photonics extends from energy generation to detection to communications and...
See optical spectrum; visible spectrum.
visible spectrum
That region of the electromagnetic spectrum to which the retina is sensitive and by which the eye sees. It extends from about 400 to 750 nm in wavelength.
aluminum gallium arsenideAluminum indium gallium phosphidecolor-rendering indexConsumergallium arsenidegallium nitride/aluminum gallium nitrideilluminatorsindustrialinfraredIR LEDlightinglighting applicationsnear infraredOpto Diode Corp.photocontrolsphotonicsRGB LEDRGBA LEDsemiconductorsspectrumultravioletUV LEDvisible spectrumwavelengthsWeb Exclusivesyellow phoshorLEDslasers

Terms & Conditions Privacy Policy About Us Contact Us
back to top
Facebook Twitter Instagram LinkedIn YouTube RSS
©2019 Photonics Media, 100 West St., Pittsfield, MA, 01201 USA,

Photonics Media, Laurin Publishing
x We deliver – right to your inbox. Subscribe FREE to our newsletters.
We use cookies to improve user experience and analyze our website traffic as stated in our Privacy Policy. By using this website, you agree to the use of cookies unless you have disabled them.