Search Menu
Photonics Media Photonics Marketplace Photonics Spectra BioPhotonics Vision Spectra Photonics Showcase Photonics ProdSpec Photonics Handbook

Materials Evolving for Lighter, Stiffer Optics

Facebook Twitter LinkedIn Email
Hank Hogan, Contributing Editor, [email protected]

Building better optical materials will impact applications in high-energy lasers, consumer devices and more.

For optical materials, less can be more: Coatings that reflect less could lead to displays that are brighter and can be seen over a wider angle. Materials that expand or contract less as the temperature fluctuates could lead to better optics. Equally important could be lightweight materials that move less.

“One basically wants very stiff optical systems, but with as low a total mass as possible,” said Marc Tricard, managing director of precision optics for Zygo Corp. of Middlefield, Conn., which makes optical components and measurement instruments, and offers design and manufacturing services.

Light yet stiff optics are “particularly important for airborne and space applications, of course, but also semiconductor applications where lower mass translates into higher system accelerations and hence higher tool throughput,” Tricard said.

New materials would be beneficial in several other areas, he added. One is in materials with a low coefficient of thermal expansion. In response to demands from defense and semiconductor customers, the industry has pushed coefficients of thermal expansion from roughly 100 parts per billion per degree kelvin down to seven or better.

High-energy laser applications

Another area of focus is high-energy laser applications. The military is interested because high-energy lasers could replace conventional weapons. Also interested are those researching fusion power, since high-energy lasers are being used to ignite the reaction. For this scenario, Zygo has developed and qualified materials capable of withstanding as much as 8 J/cm2, or nearly 60 times the intensity of sunlight. This is done for pulses of a few nanoseconds at a wavelength of 351 nm.

By repeatedly withstanding laser pulses scores of times more intense than sunlight, fused silica optics enable high-energy laser applications. Photo courtesy of Zygo Corp.

The need for relatively stiff yet lightweight materials is leading researchers to look again at single-crystal silicon. The stuff of chips and solar panels has the mechanical and thermal properties that make it an excellent compromise material, Tricard said.

Another well-known semiconductor, AlGaAs (aluminum gallium arsenide), is also promising, particularly for low-noise optical coatings, according to Dr. Garrett Cole, co-founder of Crystalline Mirror Solutions GmbH of Vienna. The startup manufactures high-quality single-crystal AlGaAs thin films on arbitrary bulk optics.

This is of commercial appeal because of the frontiers of science: As optical measurements become more precise, they demand higher optical and mechanical system quality.

It’s the latter that now constrains performance. For instance, gravitational wave detectors are kilometer-long interferometers, but a small component sets the noise floor.

A fused silica substrate with a thin film of AlGaAs (center disc) bonded to it. Due to its low mechanical loss and high optical quality, AlGaAs improves measurements in a number of scientific research areas. Photo courtesy of Garrett Cole, Crystalline Mirror Solutions.

“There are two mirrors held 4 km apart, and the system is largely limited by the 6-µm-thick film making up the reflective element of those mirrors,” Cole said. Because they are crystalline in nature, the thin films produced by Cole’s company have few defects and low mechanical loss. Just as importantly, the loss shrinks upon cooling, which is not true for all coatings. Therefore, as components are cooled and motion decreases, there’s an added bonus because the mechanical performance of the films increases.

One consequence of less mechanical loss is that devices can be made smaller, because unwanted motion as a percentage of the total cavity length is a critical constraint. If that must be below a given value, then a lower-loss material allows devices to be made smaller. That possibility is one reason why crystalline coatings have attracted the interest of defense researchers and contractors.

To produce the coating, Crystalline Mirror Solutions begins by growing an AlGaAs multilayer on a wafer via molecular beam epitaxy. The film is transferred in centimeter-sized swaths using a temporary flexible mount and then bonded to a final substrate, with care taken to eliminate voids. The resulting films are at least an order of magnitude better in terms of mechanical performance while offering optical characteristics competitive with those created by ion-beam sputtering, an alternative approach, Cole said.

A high-mechanical-quality crystalline AlGaAs coating (the white disc in the middle) helps improve optical system performance. The transparent glass cylinder to the left is a cavity spacer, and the opaque piece to the right is a mirror substrate. In a device, all pieces are in contact with each other. Photo courtesy of Jun Ye, NIST and JILA.

Dr. Jun Ye, a fellow at NIST and the University of Colorado at Boulder’s JILA research lab, makes the world’s most stable laser, with a 30-mHz-wide spectral output. Partly due to this extreme stability, Ye’s group in January demonstrated an atomic clock that’s accurate to a second over 5 billion years.

In a quest for even better lasers, Ye was involved in testing the crystalline mirror coating developed by Cole and a team at the University of Vienna. He participated because the mechanical quality of an optical system determines its response to thermal noise. “That limits how stable a laser can be made or how precise an interferometer can be used to read out length information,” Ye said of what is known as mechanical Q.

For his part, he sees the potential for a big impact from these crystalline coatings. There’s a need for high-quality optical and mechanical components across a number of scientific disciplines, according to Ye.

Consumer applications

Another sector where high-performance optical materials are attracting interest is consumer devices. A case in point comes from JDSU, the Milpitas, Calif.-based optical technology company.

Today, consumer needs drive innovation, noted Fred Van Milligen, vice president of research and development. For optical materials, an example of this can be seen in smartphones, which have ever-more-capable cameras, despite severe size and power constraints.

In general, the goal in consumer goods is to collect as much light over as wide a field of view as possible. Usually, this is done in a bandpass, with only the desired part of the spectrum getting through. Previously, this might have been for 2-D imaging in the visible, but now there’s increasing demand for 3-D and IR imaging.

Most of JDSU’s coatings involve sputtering of inorganic and organic materials onto substrates, with this often done directly on device-bearing semiconductor wafers. The coatings are carefully tailored to yield specific optical performance, and they can be complex.

“We tend to have a fair amount of layers in our coatings,” Van Milligen said. “We deliver some products with thousands of layers in them.”

Multilayer coatings are becoming more common, said Dr. E. Fred Schubert, a professor of electrical engineering at Rensselaer Polytechnic Institute in Troy, N.Y.; he co-authored an influential 2007 Nature Photonics paper on antireflection coatings.

In part, this interest in coatings is being driven by advances that allow the tailoring of a material’s optical properties by manipulating its physical characteristics, Schubert said. “We are able to control the refractive index by changing its porosity or nanoporosity.”

As a result, coatings can be designed based on calculations. Finding the sweet spot that optimizes a multilayer coating can be challenging. To do that, researchers and developers may make use of genetic algorithms, which evolve a coating’s properties from a starting point to arrive at the best solution.

Metamaterials and more

Finally, new optical materials have appeared on the horizon. For instance, Dr. Withawat Withayachumnankul, a postdoctoral researcher at the University of Adelaide in Australia, was part of a team that etched cavities into the surface of slightly conductive silicon, as described in a 2013 Advanced Optical Materials paper. The resulting metamaterial trapped and confined terahertz waves in ways that offered some significant advantages, one of which was improved imaging contrast, thanks to minimal cross-coupling between each pixel, Withayachumnankul said.

An illustration of annular cavities etched into the surface of conductive silicon. Depending on their dimensions, the cavities trap terahertz waves at different frequencies and enhance imaging. These and other metamaterials form the basis for new optical materials. Photo courtesy of Withawat Withayachumnankul, University of Adelaide.

“Moreover, since each optimized cavity can absorb nearly 100 percent of the incident power, the imaging contrast is improved further,” he added.

The next step in the research will be to form a complete imaging system by integrating a thermal detector to read out the temperature change when terahertz waves strike the cavity array. The technique has attracted commercial interest, Withayachumnankul said.

Metamaterials in general allow the engineering of properties and so could enable new applications, he added. An example might be an optical tunable flat lens that actively responds to incoming light with polarization changes.

Another way to make new optical materials is to grow them. A research team from New York University, Harvard University and Dow Chemical Co. revealed in a 2012 Nature paper a self-assembly technique based on small particles suspended within a fluid. Such colloidal manufacturing could be very inexpensive and suitable for fabricating materials on plastics or other flexible substrates that can’t tolerate high temperatures.

Dr. Vinothan Manoharan, a chemical engineering and physics professor at Harvard who was a member of the research team, is investigating the technique as a way to produce photonic inks – materials inspired by bird feathers that generate color through interference. Since light isn’t absorbed, photonic inks might retain their hue longer than traditional pigments. Also, this structure-based approach relies on ambient light, making photonic inks potentially useful in low-energy-consuming electronic displays.

At present, the colloid-created photonic inks can change color in response to changes in their chemical environment, although Manoharan noted that doing so electronically would be best for displays. Being researched is how to make photonic inks mimic the appearance of traditional pigments. Red, in particular, has proved difficult to achieve. In addition, because these colors depend upon diffraction and interference, another area of improvement is being researched.

“You also have to get a color that doesn’t change as you change the viewing angle,” Manoharan said.

Photonics Spectra
Mar 2014
AmericascamerascoatingsConsumerdefenseDisplaysEuropeFeaturesflexible displaysfused silica opticshigh-energy laserimagingindustriallenseslight sourcesmaterialsmirrorsopticssingle-crystal siliconthermal expansionWaferslasers

back to top
Facebook Twitter Instagram LinkedIn YouTube RSS
©2023 Photonics Media, 100 West St., Pittsfield, MA, 01201 USA, [email protected]

Photonics Media, Laurin Publishing
x Subscribe to Photonics Spectra magazine - FREE!
We use cookies to improve user experience and analyze our website traffic as stated in our Privacy Policy. By using this website, you agree to the use of cookies unless you have disabled them.