Search Menu
Photonics Media Photonics Buyers' Guide Photonics Spectra BioPhotonics EuroPhotonics Vision Spectra Photonics Showcase Photonics ProdSpec Photonics Handbook
More News

NIST Cracks Tough Nut

Facebook Twitter LinkedIn Email Comments
GAITHERSBURG, Md., Dec. 30, 2008 – A technique discovered by researchers at the National Institute of Standards and Technology (NIST) could give a boost to the semiconductor industry.
The researchers developed a method to measure the toughness – the resistance to fracture – of the thin insulating films that play a critical role in high-performance integrated circuits (ICs). The new technique could improve the reliability and manufacturability of ICs and, better yet, it’s one that state-of-the-art microelectronics manufacturers can use with equipment they already own.
At issue is the mechanical strength of so-called “low-k” dielectric layers – electrically insulating films only a couple of micrometers thick that are interleaved between layers of conductors and components in microprocessor chips and other high-performance semiconductor devices.


This is a typical low-k film test for material toughness using the new NIST technique. The indentation instrument that punches the triangular hole registers the forces involved. That, plus the length of the resulting cracks, determines the toughness of the film, which is about 2.4 microns thick (color added for clarity). Image courtesy of NIST.

As IC features such as transistors have become ever smaller and crammed more closely together, designers are preventing electrical interference, or crosstalk, by making the insulating films more and more porous with nanoscale voids, but this has made them more fragile. Brittle fracture failure of low-k insulating films remains a problem for the industry, affecting both manufacturing yields and device reliability. To date, there has been no accurate method to measure the fracture resistance of such films, which makes it difficult to design improved dielectrics.

NIST researchers believe that they have found an answer to the measurement problem in a new adaptation of a materials test technique called nanoindentation, which works by pressing a sharp, hard object – a diamond tip – and observing how much pressure it takes to deform the material. For roughly 20 years, researchers have known how to measure elasticity and plasticity – the forces needed to bend a material either temporarily or permanently – of materials at very small scales with nanoindenters. But toughness, the force needed to actually break the material, has been a bit more difficult to determine. Thin films were particularly problematic because they must be layered on top of another stronger material, such as a silicon wafer.

The new technique requires a slight modification of the nanoindentation equipment. The probe must have a sharper, more acute point than normally used as well as a hefty dose of theory. Pressing carefully on the dielectric film generates cracks as small as 300 nm, which are measured by electron microscopy. Just how the cracks form depends on a complex interaction involving indentation force, film thickness, film stress and the elastic properties of the film and the silicon substrate. These variables are plugged into a new fracture mechanics model that predicts not only the fracture toughness but also another key value: the critical film thickness for spontaneous fracture.

Using this methodology, device manufacturers will be able to eliminate some candidate interconnect dielectric films from consideration without further expensive device testing. The measurement technique and model were published in a two-part series in the Journal of Materials Research.*

For more information, visit:


D.J. Morris and R.F. Cook. Indentation fracture of low-dielectric constant films: Part I. Experiments and observations. J. Mater. Res., Vol. 23, No. 9, p. 2429.

D.J. Morris and R.F. Cook. Indentation fracture of low-dielectric constant films: Part II. Indentation fracture mechanics model. J. Mater. Res., Vol. 23, No. 9, p. 2443.
Dec 2008
The use of atoms, molecules and molecular-scale structures to enhance existing technology and develop new materials and devices. The goal of this technology is to manipulate atomic and molecular particles to create devices that are thousands of times smaller and faster than those of the current microtechnologies.
The technology of generating and harnessing light and other forms of radiant energy whose quantum unit is the photon. The science includes light emission, transmission, deflection, amplification and detection by optical components and instruments, lasers and other light sources, fiber optics, electro-optical instrumentation, related hardware and electronics, and sophisticated systems. The range of applications of photonics extends from energy generation to detection to communications and...
dielectic layersgreen photonicsHigh-Performance Integrated CircuitsindustrialJournal of Materials ResearchLow-KmicroelectronicsMicroscopynanonanoindentationnanotechnologyNational Institute of Standards and TechnologyNews & FeaturesNISTphotonicssemiconductor industrysemiconductors

back to top
Facebook Twitter Instagram LinkedIn YouTube RSS
©2019 Photonics Media, 100 West St., Pittsfield, MA, 01201 USA,

Photonics Media, Laurin Publishing
x We deliver – right to your inbox. Subscribe FREE to our newsletters.
We use cookies to improve user experience and analyze our website traffic as stated in our Privacy Policy. By using this website, you agree to the use of cookies unless you have disabled them.