Search Menu
Photonics Media Photonics Buyers' Guide Photonics EDU Photonics Spectra BioPhotonics EuroPhotonics Industrial Photonics Photonics Showcase Photonics ProdSpec Photonics Handbook
More News
Email Facebook Twitter Google+ LinkedIn Comments

Novel Design Simplifies VECSEL Fabrication

Photonics Spectra
Nov 2007
Intracavity microlens provides focusing and matches pump light to resonator mode.

Breck Hitz

There are several advantages in using the end facet of an optical fiber as the output mirror of a vertical external cavity surface-emitting laser (VECSEL). For one thing, it’s easy to couple the VECSEL’s output into the fiber. And if the VECSEL is optically pumped, the fiber provides an ideal mechanism to launch the pump power. Recently, Nicolas Laurand and his colleagues at the Institute of Photonics at the University of Strathclyde in Glasgow, UK, demonstrated such a laser that incorporates a unique intracavity microlens to stabilize the resonator (Figure 1). This type of laser is likely to find applications in spectroscopy, metrology and optical communications.


Figure 1. The VECSEL resonator is defined by its two reflectors, the distributed Bragg reflector (DBR) on the bottom and the dielectric mirror on the fiber facet, which is the laser’s output coupler. The laser can be wavelength-tuned by displacing the fiber vertically. Images reprinted with permission of Optics Letters.

The idea of using a fiber facet as a VECSEL mirror is not new and has been explored previously. But a resonator with two flat reflectors — such as a fiber facet and a distributed Bragg reflector — cannot support a stable mode in the absence of any form of intracavity focusing. In some cases, thermal gradients within the laser itself can provide the necessary focusing.

However, these gradients and, hence, the resonator stability, are strongly dependent on power levels and are, therefore, unsatisfactory for many applications. As an alternative, researchers have polished a concave surface on the fiber facet, thereby providing intracavity focusing that is independent of power.

Now the Strathclyde researchers have substituted an intracavity microlens for the concave surface, a step that they say significantly simplifies device fabrication.

There are additional advantages to substituting a microlens for the concave facet. Because the VECSEL’s output coupler (i.e., the fiber facet) is flat, there is necessarily a beam waist there, facilitating coupling into the fiber. Also, for an optically pumped VECSEL, the waist is inherently close in size to the fiber’s mode, ensuring good overlap between the pump light and the intracavity laser mode.

Figure 2. The output power was greatest for the smallest gap between the fiber facet and the microlens, even though that spacing didn’t optimize coupling into the fiber. The explanation lies in the increased pump-power density accompanying the 23-μm gap. The inset shows a superposition of sequential spectra as the laser was tuned. Single longitudinal- and transverse-mode oscillation occurred except near the edges, where a second longitudinal mode reached threshold.

The scientists fabricated their microlenses from a homemade epoxy but believe that commercial polymers alternatively could be used with no degradation in performance. For the results described here, they used microlenses of 44 μm in diameter. The laser gain was provided by 10 InGaAs strain-compensated quantum wells that were positioned at the maxima of the intracavity standing wave. The mirror coated onto the fiber facet reflected 95 percent of the 1.055-μm laser wavelength but was highly transmissive to the 810-nm pump light. The scientists mounted the fiber on a precision X-Y-Z translation stage so that they could carefully adjust the spacing between the fiber facet and the microlens.

By adjusting that spacing, they continuously tuned the laser between 1028 and 1041 nm (Figure 2). The resonator’s longitudinal mode spacing was approximately as great as the gain spectrum, so only at the extremes of this tuning curve did they observe more than a single longitudinal mode oscillating.
Optics Letters, Oct. 1, 2007, pp. 2831-2833.

The science of measurement, particularly of lengths and angles.
optical fiber
A thin filament of drawn or extruded glass or plastic having a central core and a cladding of lower index material to promote total internal reflection (TIR). It may be used singly to transmit pulsed optical signals (communications fiber) or in bundles to transmit light or images.
The technology of generating and harnessing light and other forms of radiant energy whose quantum unit is the photon. The science includes light emission, transmission, deflection, amplification and detection by optical components and instruments, lasers and other light sources, fiber optics, electro-optical instrumentation, related hardware and electronics, and sophisticated systems. The range of applications of photonics extends from energy generation to detection to communications and...
Communicationsfiber opticsmetrologyoptical fiberoutput mirrorphotonicsResearch & Technologyvertical external cavity surface-emitting laser

Terms & Conditions Privacy Policy About Us Contact Us
back to top
Facebook Twitter Instagram LinkedIn YouTube RSS
©2018 Photonics Media, 100 West St., Pittsfield, MA, 01201 USA,

Photonics Media, Laurin Publishing
x Subscribe to Photonics Spectra magazine - FREE!
We use cookies to improve user experience and analyze our website traffic as stated in our Privacy Policy. By using this website, you agree to the use of cookies unless you have disabled them.