Photonics Handbook

An integrating sphere’s function is to spatially integrate radiant flux (light). However, before one can optimize a sphere design for a particular application, it is important to understand how...

The wavelength range of commercially available LEDs with single-element output power of at least 5 mW is 275 to 950 nm. Each wavelength range is made from a specific semiconductor material family,...

An interferometer is an instrument that compares the position or surface structure of two objects. The basic two-beam division of amplitude interferometer components consists of a light source, a...

The optical materials selected for an optical system depend upon the application, the required system performance and the environment in which the system is to perform; thus the materials’...

Double-sided processing is a batch-type process that uses planetary action — generally with loose, abrasive particles suspended in a liquid vehicle — to abrade material almost equally...

One of the most critical elements of any time-resolved spectroscopy and dynamics experiment is the optical delay line. A typical optical delay line consists of a retroreflector or folding mirrors on...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

Since their invention in the late 1960s, charge-coupled devices, also called CCDs, have found widespread use in imaging applications. Electronic cameras based on CCD technology are used in...

Image intensification, the basis of night vision, is a complex conversion of energy particles that occurs within a vacuum tube. An image-intensifier system works by collecting photons through an...

An optical time-domain reflectometer sends short pulses of light into a fiber and measures its reflections as a function of time. The delay of these reflections to the detector as well as their...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

Photonics Rules of Thumb Scientists and engineers tend to want to answer simple relational questions with a blackboard covered with equations, even when questioners just want a rough estimate to...

With a specific gravity of 1.85 g/cm3, beryllium is the lightest metal that is workable. It is 45 percent lighter than aluminum and approximately five times as stiff. Its stiffness to weight ratio...

Abbe Error — Linear off-axis errors introduced by angular deviations coupled to a moment arm at the point of interest on stage mounted devices (θ in Figure 1). The effect of Abbe error...

The basic setup in laser perforation includes a pulsed laser, a lens and either a moving mirror, a rotating web or both. Each laser pulse creates a hole in the material. During the blank time in...

Charged-injection device imagers are metal-oxide semiconductor (MOS) detectors that can be fabricated using PMOS, NMOS and CMOS integrated circuit technology, and may be configured as a...

Adhesives for fiber optic components that perform well on glass, metal, ceramic and most plastic substrates provide excellent chemical and solvent resistance. They also can act as an electrical...

The ubiquitous Nd:YAG laser has played many roles over the years. For the military, it has provided rangefinding and target designation capabilities. When used with nonlinear optics or as a pump...

Measuring pulsed-beam lasers has generally required the use of a CCD array profiler. This is a reasonable solution for low-power lasers in the UV and visible wavelength range, but these require...

Intensity and uniformity can be described using different physical attributes, which makes interpreting requirements somewhat confusing. This article intends to provide an explanation and serve as a...

A lens collects light from a point on an object and focuses it to a corresponding conjugate point on an image. Under most conditions, the lens fails at this task because of some error in the...

Like other CTDs, the CID imager uses hundreds of thousands (up to 4 million) pixel elements to capture optical images, and converts the light into an electronic charge which may be displayed on a...

A chart listing angle conversions – Degree, Minute, Second, Radian, Milliradian, Circumference and Quadrant Angle Conversions Angle Conversions degree min sec rad mrad circumference...

DATA TABLES: OPTICAL THIN-FILM MATERIALS Identification Physical Parameters Material Name Material Formula Transparent Region(µm) (see note a) Index at Wavelength...

Hyperspectral imaging spectroscopy has developed dramatically from a large, complex, remote-sensing satellite- or aircraft-based system into a rugged, compact, economically priced imaging and...

The common polycrystalline materials used for optical thin-film materials do not satisfy the requirements of telecommunications because of the instabilities caused by moisture absorption in their...

Reflected-ultraviolet imaging is a rather mysterious area of the imaging field. There is relatively little actual UV imagery to be found on the Internet or in the literature compared to near-infrared...

That portion of the spectrum that the eye can see — and its rainbow of colors — is rather small, covering approximately 360 to 830 nm. What colors we perceive depends on wavelength, while...

Photonic components are key elements for the information technology (IT). Photonics technology covers the generation of information (cameras, sensors), its transportation (optical communication),...

Infrared system design is not, like some circuit design, a synthetic process. One cannot start by stating the problem and proceeding in an orderly fashion to a final solution. Rather, we guess a...

If we were to estimate the output of a CCD or thermal camera, we would typically draw an image over the detectors, aligning the image with the detector axes. We show it this way because it’s...

Designing devices that incorporate ultrathin films is an important means of enhancing yields. However, characterizing ultrathin films provides a challenge for mainstream metrology tools such as...

Optics can be contaminated in many ways. Contamination can be kept to a minimum by returning the optics to their case after use or by covering the optics for protection from the outside environment....

Equation (1) is known as the Gaussian form of the lens equation, after the mathematician Karl F. Gauss. Equation (2), first derived by Sir Isaac Newton, is the Newtonian form of a lens equation. The...

Illumination design has developed rapidly to include not only automotive headlamps and street lamps, but also backlit displays, fluorescent panel lighting, light-emitting diode or laser sources, and...

While some design engineers know exactly what they need from their laser diode, others may choose a partner to navigate what can be a complex development process. Laser diode manufacturers know which...

Manufacturing the laser diode is complicated by the existence of multiple proprietary techniques and intellectual property barriers together with complex device physics and unique materials. ...

Material Coefficient of Expansion(×10-6 per °C) Density (lbs/cubic in.) Aluminum 23.8 0.10 Brass (cast) 18.8 0.30 Carbon (diamond) 1.2 0.25 Carbon (graphite) 7.9 - Copper 16.2 0.32...

Camera resolution depends upon the optical blur diameter and the detector size. Schade combined these to create an equivalent resolution that is a function of Fλ/d where F is the focal ratio,...

Just as an electronic connector provides a pluggable connection between electronic circuits, a fiber optic connector provides an optical one. The goal is joining a fiber to a transmitter, receiver or...

Progressive assembly operations such as guiding, gluing and bonding often take place around a static package in three-dimensional space. Integrating the different mechanical systems to ensure that...

There is a growing market for imaging systems that provides an immediate, slow-motion view of a process that allows one to see events that happen too quickly for the human eye to perceive or...

Attentuation Region (or Blocking) The spectral region over which very low transmission is required. Attenuation requirements are generally specified in percent transmission over a given spectral...

The digital camera represents an integration of optics, mechanics and electronics consisting of three layers (Figures 1a, b and c). The top and the middle layers are printed circuit boards (PCBs),...

Photometric Units SI Units Quantity Unit Luminous flux lumen lm Luminous intensity candela cd Luminance cd/m2 Illuminance lm/m2 lx Non-SI Units Luminous Intensity ...

Radiometry involves several activities. The two most common are the description and measurement of optical radiation, and, starting with the knowledge of some aspects of optical radiation at one...

ACOUSTO-OPTIC SCANNING DEVICES: CHARACTERISTICS MODULATORS Material Bandwidth (MHz) Rise Time (ns) Acousto Input Power (W) (Saturation) Material Wavelength Range...

Images are produced by many means: cameras, x-ray machines, electron microscopes, radar and ultrasound. They are used in the entertainment, medical, scientific and business industries; for security...

All optical spectrometry techniques rely on the measurement of radiant power. The configuration of the instrument varies based on the measurement technique: absorption, emission, luminescence, or...