Photonics Handbook

Diffraction gratings are optical components with a periodic structure that separate light into beams traveling in predictable directions based on their wavelength. The grating acts as the dispersive...

Photonics is the study of light and other types of radiant energy whose quantum unit is the photon. The impact of photonics on research, technology, navigation, culture, astronomy, forensics, and...

Except for direct illumination from the sun, laser, or other light source, everything we see or detect is ultimately scattered light. Light can be scattered or rescattered during its propagation to...

Electrical engineers are very familiar with the effects of shot noise, thermal noise, flicker noise and crosstalk, and recognize how these effects can reduce the signal-to-noise ratio (SNR) in their...

Silicon photonics is widely considered a key enabling technology for further development of optical interconnect solutions needed to address growing traffic on the internet. From the first submarine...

Many common spectroscopic measurements require the coordinated operation of a detection instrument and light source, as well as data acquisition and processing. Integration of individual components...

By its original definition, a nanopositioning device is a mechanism capable of repeatedly delivering motion in increments as small as one nanometer. Lately demands from industry and research have...

As recently as five years ago, shopping for a microscope light source was fairly straightforward. For routine applications, it was tungsten halogen, typically 100 W, while for fluorescence, it was an...

Profiling beams under 10 µm in size is one of the more challenging beam profiling applications. There are numerous reasons for this, including the very small size. Focal plane arrays commonly...

Given the pace at which technology advances, there always seems to be a learning curve. With the abundance of consumer electronics available, there typically is no right or wrong way to use these...

Optical fibers are made from either glass or plastic. Most are roughly the diameter of a human hair, and they may be many miles long. Light is transmitted along the center of the fiber from one end...

Optical design software allows the user to develop a configuration of optical elements that manipulate the trajectory of light for the purposes of creating an image, illuminating a target, coupling...

As you operate your laser, only a portion of the electrical power sourced from your laser driver converts to light energy. The remainder turns to heat, and the buildup of that thermal energy presents...

Laser development for the microscopy market continues to be driven by key trends in applications, which currently include superresolution techniques, multiphoton applications in optogenetics and...

A bench power supply should be thoroughly tested and characterized before it is used to power a laser. The quality of the controls and safety measures incorporated into a bench supply will need to be...

Neodymium-doped crystals and glasses such as Nd:YAG (neodymium:yttrium aluminum garnet) have long been used as laser gain materials. Optically pumped, they produce an output wavelength close to 1...

The use of precision polymer optics is becoming an increasing necessity today as products demand sophisticated light handling components to achieve desired results. Polymer optics can be thought of...

Over 60 years have passed since the first demonstration of a laser in 1960. After the initial spark of interest, lasers were for a while categorized as “a solution waiting for a problem,”...

What are thin-film coatings? The purpose of any optical thin-film coating is to modify the transmittance and reflectance properties of the substrate material to which they are applied. Most coatings...

An integrating sphere’s function is to spatially integrate radiant flux (light). However, before one can optimize a sphere design for a particular application, it is important to understand how...

Infrared system design is not, like some circuit design, a synthetic process. One cannot start by stating the problem and proceeding in an orderly fashion to a final solution. Rather, we guess a...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

That portion of the spectrum that the eye can see — and its rainbow of colors — is rather small, covering approximately 360 to 830 nm. What colors we perceive depends on wavelength, while...

Image intensification, the basis of night vision, is a complex conversion of energy particles that occurs within a vacuum tube. An image-intensifier system works by collecting photons through an...

All optical spectrometry techniques rely on the measurement of radiant power. The configuration of the instrument varies based on the measurement technique: absorption, emission, luminescence, or...

Radiometry involves several activities. The two most common are the description and measurement of optical radiation, and, starting with the knowledge of some aspects of optical radiation at one...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

Illumination design has developed rapidly to include not only automotive headlamps and street lamps, but also backlit displays, fluorescent panel lighting, light-emitting diode or laser sources, and...

Intensity and uniformity can be described using different physical attributes, which makes interpreting requirements somewhat confusing. This article intends to provide an explanation and serve as a...

Manufacturing the laser diode is complicated by the existence of multiple proprietary techniques and intellectual property barriers together with complex device physics and unique materials. ...

Images are produced by many means: cameras, x-ray machines, electron microscopes, radar and ultrasound. They are used in the entertainment, medical, scientific and business industries; for security...

When physical structures get very small — on the order of molecular or atomic sizes with one or more dimensions on the nanoscale — their behavior and interactions with energy, including...

Reading and writing systems for polygonal scanners differ in the use of the scanner. However, many performance characteristics are similar for both. In writing applications, a light source, usually a...

Simple Meniscus Lens The simple meniscus lens is almost universally used in inexpensive cameras. To get an image of good quality it must be used with a separate aperture stop, reducing the...

Unlike an edge emitter, a VCSEL has a maximum operating power that is not limited by catastrophic optical damage of the exit aperture because its aperture is larger and its PN junction does not...

The applications where rapid detection of light is a must are many. They include a wide variety: semiconductor inspection, gene sequencing, oil well logging and high-energy physics. The reasons for...

There are three fundamentally different dispersive phenomena in optical fiber, of which polarization mode dispersion (PMD) is the most complex. In digital multimode fiber systems, a light pulse...

In the beginning, automated inspection focused on the camera and optics, the algorithms, the interface hardware and the processor. Only rarely was attention paid to the lighting system or lighting...

Imaging has long been used in industrial processes to measure, monitor, control, or otherwise manage the production of goods. The challenge to the process designer is to develop a tool that captures...