Photonics Handbook

Laser diodes vary widely in their wavelengths, powers, spectra and beam quality. Yet they share two fundamental components with all other lasers: an optical amplifier and a resonator that confines...

Early fiber lasers were inefficient and limited to low powers, until more effective methods emerged to deliver the pump light into the cladding. Valentin Gapontsev, founder and CEO of IPG Photonics,...

Silicon photonics is widely considered a key enabling technology for further development of optical interconnect solutions needed to address growing traffic on the internet. From the first submarine...

Materials processing with lasers is actually a broad term for a diverse range of applications. The major categories of these uses, and the lasers that service them, are summarized Table 1. At one...

Since its first successful operation in 1960 at Hughes Research Labs, the laser technology has been at the center of innovation and research. Semiconductor lasers first made their appearance in 1962...

By its original definition, a nanopositioning device is a mechanism capable of repeatedly delivering motion in increments as small as one nanometer. Lately demands from industry and research have...

Laser development for the microscopy market continues to be driven by key trends in applications, which currently include superresolution techniques, multiphoton applications in optogenetics and...

Neodymium-doped crystals and glasses such as Nd:YAG (neodymium:yttrium aluminum garnet) have long been used as laser gain materials. Optically pumped, they produce an output wavelength close to 1...

The optical materials selected for an optical system depend upon the application, the required system performance and the environment in which the system is to perform; thus the materials’...

Double-sided processing is a batch-type process that uses planetary action — generally with loose, abrasive particles suspended in a liquid vehicle — to abrade material almost equally...

The wavelength range of commercially available LEDs with single-element output power of at least 5 mW is 275 to 950 nm. Each wavelength range is made from a specific semiconductor material family,...

What are thin-film coatings? The purpose of any optical thin-film coating is to modify the transmittance and reflectance properties of the substrate material to which they are applied. Most coatings...

The first high-reflectance mirror coatings for the UV and vacuum UV (VUV) were of the Al + MgF2 type produced in the late 1950s. Coatings of this design are still used today for multigas cavity...

Over 60 years have passed since the first demonstration of a laser in 1960. After the initial spark of interest, lasers were for a while categorized as “a solution waiting for a problem,”...

With a specific gravity of 1.85 g/cm3, beryllium is the lightest metal that is workable. It is 45 percent lighter than aluminum and approximately five times as stiff. Its stiffness to weight ratio...

Photonics Rules of Thumb Scientists and engineers tend to want to answer simple relational questions with a blackboard covered with equations, even when questioners just want a rough estimate to...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

DATA TABLES: OPTICAL THIN-FILM MATERIALS Identification Physical Parameters Material Name Material Formula Transparent Region(µm) (see note a) Index at Wavelength...

Reflected-ultraviolet imaging is a rather mysterious area of the imaging field. There is relatively little actual UV imagery to be found on the Internet or in the literature compared to near-infrared...

Designing devices that incorporate ultrathin films is an important means of enhancing yields. However, characterizing ultrathin films provides a challenge for mainstream metrology tools such as...

Optics can be contaminated in many ways. Contamination can be kept to a minimum by returning the optics to their case after use or by covering the optics for protection from the outside environment....

Manufacturing the laser diode is complicated by the existence of multiple proprietary techniques and intellectual property barriers together with complex device physics and unique materials. ...

All optical spectrometry techniques rely on the measurement of radiant power. The configuration of the instrument varies based on the measurement technique: absorption, emission, luminescence, or...

Optics today needs alchemy, and the forces that motivate microchip technology are a key reason why. Today, light can transmit and process digital information as well as electricity can — in...

The scope of optical spectroscopic instrumentation is indeed very broad. Many analytical methods rely on the interaction of radiation with matter and are often described in the context of quantum and...

Imaging has long been used in industrial processes to measure, monitor, control, or otherwise manage the production of goods. The challenge to the process designer is to develop a tool that captures...

Unlike an edge emitter, a VCSEL has a maximum operating power that is not limited by catastrophic optical damage of the exit aperture because its aperture is larger and its PN junction does not...

NSOM is suitable for studies on the mesoscopic scale (several tens to hundreds of molecular dimensions). It has become an important tool in research and applications of semiconductors, organic layers...

Particle image velocimetry (PIV) is an experimental tool in fluid mechanics and aerodynamics. The basic principle involves photographic recording of the motion of microscopic particles that follow...