CAMERAS & IMAGING

FMC-MIPI is an HPC. FMC provides connectivity between FPGA on a carrier and 2x MIPI CSI-2 4 lanes input and 2x MIPI DSI2 4 lanes output interfaces. Module provides conversion from MIPI CSI-2 to parallel interface or vice versa to 2x MIPI CSI2 4 lanes output. 2 MIPI based sensor/camera and 2 MIPI based displays could be supported concurrently. 2 sensors cameras. Interfaces to carrier cards. Features: LP and HP modes 4 Lanes I2C interface MIPI CSI-2 input MIPI DSI output

PCIe 3.0 eight-connection CoaXPress frame grabber Eight CoaXPress CXP-6 connections: 5000 MB/s camera bandwidth Connect up to eight CoaXPress cameras to one card PCIe 3.0 (Gen 3) x8 bus: 6700 MB/s bus bandwidth Feature-rich set of 10 digital I/O lines Extensive camera control functions Memento event logging tool

FG-650CL is an FPGA based imaging solution that supports BASE, MEDIUM, FULL and Extended FULL CameraLink compatible cameras. The hardware is a PC plugin card but can also be used in an embedded fashion. The solution offers 8 lanes of Gen3 PCIe, PXIe for host communication and Stand Alone . An FMC-CL Camera Link FMC card is attached to the base card for interfacing to the cameras. Features: Open FPGA PXIe, PCIe Stand Alone CL interface LPC, HPC 2 x SATA-3 I/O capabilities

FG-650CL is an FPGA based imaging solution that supports BASE, MEDIUM, FULL and Extended Full CameraLink compatible cameras. The hardware is a PC plugin card but can also be used in an embedded fashion. The solution offers 8 lanes of Gen3 PCIe, PXIe for host communication and Stand Alone. An FMC-CL Camera Link FMC card is attached to the base card for interfacing to the cameras. Features: Open FPGA PXIe, PCIe Stand Alone CL interface LPC, HPC 2 x SATA-3 I/O capabilities

FMC/CL is a Camera Link FMC (FPGA Mezzanine Module) that interfaces to quad BASE, MEDIUM, and dual FULL and Extended FULL Camera Link compatible cameras. The FMC/CL has variety of I/O capabilities – 2 x SATA connectors and 4 CL connectors that can also be used as a general purpose I/O. Features: Dual, Quad, Medium modes Full and Extended modes PoCL and HPC ESD protection Dual SATA I/O capabilites

The FireBird Quad CXP-12 3PE8 supports either one 4-link camera, two 2-link cameras, or up to four 1-link cameras, all up to CXP-12. Each CoaXPress link supports up to 12.5 Gbps data rates, along with device power up to 13 W and device control at up to 42 Mbps – all on a single coax cable. Links can be concatenated. Very long cable lengths supported – up to 3 5m at 12.5 Gbps and 100 m at 3.125 Gbps.

Board has been optimized for cost to have wide appeal for a range of applications. It is ideal for use with the latest range of small, lower-priced single-link CoaXPress cameras. CoaXPress in this combination offers an affordable solution including high bandwidths, real-time triggering, long cable lengths and the robustness and reliability of a dedicated vision standard.

FireBird supports the latest version 2.0 Camera Link specification, including both 80-bit modes – often referred to as Camera Link “Deca”, at clock rates up to 85 MHz. The 4-lane Gen2 interface used on the FireBird is fast enough to support full 80-bit data rate. Also supports capture from one Full, Medium or Base camera or two simultaneous Base cameras.

Four-connection CoaXPress CXP-12 frame grabber Four CoaXPress CXP-12 connections: 5000 MB/s camera bandwidth PCIe 3.0 (Gen 3) x8 bus: 6700 MB/s bus bandwidth Feature-rich set of 20 digital I/O lines Extensive camera control functions Memento event logging tool

For image acquisition, storage, processing, and display.