Photonics Handbook

Electrical engineers are very familiar with the effects of shot noise, thermal noise, flicker noise and crosstalk, and recognize how these effects can reduce the signal-to-noise ratio (SNR) in their...

By its original definition, a nanopositioning device is a mechanism capable of repeatedly delivering motion in increments as small as one nanometer. Lately demands from industry and research have...

As recently as five years ago, shopping for a microscope light source was fairly straightforward. For routine applications, it was tungsten halogen, typically 100 W, while for fluorescence, it was an...

Profiling beams under 10 µm in size is one of the more challenging beam profiling applications. There are numerous reasons for this, including the very small size. Focal plane arrays commonly...

Given the pace at which technology advances, there always seems to be a learning curve. With the abundance of consumer electronics available, there typically is no right or wrong way to use these...

Optical fibers are made from either glass or plastic. Most are roughly the diameter of a human hair, and they may be many miles long. Light is transmitted along the center of the fiber from one end...

Flat optics generally perform three main functions: They transmit light (windows), reflect light (mirrors), and fold light (prisms). While most optical manufacturers make spherical and flat optics, a...

The optical materials selected for an optical system depend upon the application, the required system performance and the environment in which the system is to perform; thus the materials’...

Over 60 years have passed since the first demonstration of a laser in 1960. After the initial spark of interest, lasers were for a while categorized as “a solution waiting for a problem,”...

The first high-reflectance mirror coatings for the UV and vacuum UV (VUV) were of the Al + MgF2 type produced in the late 1950s. Coatings of this design are still used today for multigas cavity...

The use of precision polymer optics is becoming an increasing necessity today as products demand sophisticated light handling components to achieve desired results. Polymer optics can be thought of...

Applications facilitated by tunable lasers fall into two categories: situations in which one or more discrete wavelengths are not available from any single- or multiline fixed-wavelength laser, or...

An optical coating engineer is frequently confronted with a difficult specification for a coating. Often the difficulty in the specification results from the particular form of the optical system. If...

The basic difference between the household mirror and the optical mirror is that one is coated on the back surface and the other is coated on the front. For optical applications, a front-surface...

Just as an electronic connector provides a pluggable connection between electronic circuits, a fiber optic connector provides an optical one. The goal is joining a fiber to a transmitter, receiver or...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

With a specific gravity of 1.85 g/cm3, beryllium is the lightest metal that is workable. It is 45 percent lighter than aluminum and approximately five times as stiff. Its stiffness to weight ratio...

The common polycrystalline materials used for optical thin-film materials do not satisfy the requirements of telecommunications because of the instabilities caused by moisture absorption in their...

Reflected-ultraviolet imaging is a rather mysterious area of the imaging field. There is relatively little actual UV imagery to be found on the Internet or in the literature compared to near-infrared...

To the novice or casual user of optics, the acquisition of an optical system can be a very difficult experience. Failure to understand the ground rules can result in unnecessarily high cost, late...

Optics can be contaminated in many ways. Contamination can be kept to a minimum by returning the optics to their case after use or by covering the optics for protection from the outside environment....

The ubiquitous Nd:YAG laser has played many roles over the years. For the military, it has provided rangefinding and target designation capabilities. When used with nonlinear optics or as a pump...

Lenses come in a variety of shapes, sizes and materials. They can be made of a single piece of glass or have multiple elements; their surfaces can be spherical, aspheric or cylindrical; they can be...

Many linear materials proceseqsing applications call for lasers with continuous-wave (CW) output. For example, early stereolithography systems were based on CW lasers such as argon-ion or HeCd. To...

For any discussion of laser beam diagnostics, it is first necessary to define some terms that characterize beam properties. Broad definitions can include measurements of laser energy or power,...

Laser diodes vary widely in their wavelengths, powers, spectra and beam quality. Yet they share two fundamental components with all other lasers: an optical amplifier and a resonator that confines...

An indicator of how well the entire system performs is a measurement called bit-error-ratio (BER). Acceptable BERs range from one error per billion to one per trillion bits transmitted. It is rare...

There are three fundamentally different dispersive phenomena in optical fiber, of which polarization mode dispersion (PMD) is the most complex. In digital multimode fiber systems, a light pulse...