Photonics Handbook

Diffraction gratings are optical components with a periodic structure that separate light into beams traveling in predictable directions based on their wavelength. The grating acts as the dispersive...

Electrical engineers are very familiar with the effects of shot noise, thermal noise, flicker noise and crosstalk, and recognize how these effects can reduce the signal-to-noise ratio (SNR) in their...

Single-crystal sapphire has been the material of choice for defense and other applications that require extremely durable optics, but aluminum oxynitride (ALON) and magnesium aluminate (spinel) have...

In their earliest forms, UV bandpass filters that were optimized for wavelengths less than 400 nm, such as the Schott UG or the Hoya U-series, were constructed of absorbing compounds in glass. Such...

The first high-reflectance mirror coatings for the UV and vacuum UV (VUV) were of the Al + MgF2 type produced in the late 1950s. Coatings of this design are still used today for multigas cavity...

What are thin-film coatings? The purpose of any optical thin-film coating is to modify the transmittance and reflectance properties of the substrate material to which they are applied. Most coatings...

An integrating sphere’s function is to spatially integrate radiant flux (light). However, before one can optimize a sphere design for a particular application, it is important to understand how...

The optical materials selected for an optical system depend upon the application, the required system performance and the environment in which the system is to perform; thus the materials’...

DATA TABLES: OPTICAL THIN-FILM MATERIALS Identification Physical Parameters Material Name Material Formula Transparent Region(µm) (see note a) Index at Wavelength...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

Image intensification, the basis of night vision, is a complex conversion of energy particles that occurs within a vacuum tube. An image-intensifier system works by collecting photons through an...

Charged-injection device imagers are metal-oxide semiconductor (MOS) detectors that can be fabricated using PMOS, NMOS and CMOS integrated circuit technology, and may be configured as a...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

With a specific gravity of 1.85 g/cm3, beryllium is the lightest metal that is workable. It is 45 percent lighter than aluminum and approximately five times as stiff. Its stiffness to weight ratio...

Adhesives for fiber optic components that perform well on glass, metal, ceramic and most plastic substrates provide excellent chemical and solvent resistance. They also can act as an electrical...

Reflected-ultraviolet imaging is a rather mysterious area of the imaging field. There is relatively little actual UV imagery to be found on the Internet or in the literature compared to near-infrared...

Designing devices that incorporate ultrathin films is an important means of enhancing yields. However, characterizing ultrathin films provides a challenge for mainstream metrology tools such as...

The basic difference between the household mirror and the optical mirror is that one is coated on the back surface and the other is coated on the front. For optical applications, a front-surface...

Spectral selection is a powerful tool that enhances conventional imaging tremendously. Most imaging systems, including the human eye, are designed to image light over a broad range of the spectrum....

All optical spectrometry techniques rely on the measurement of radiant power. The configuration of the instrument varies based on the measurement technique: absorption, emission, luminescence, or...

When physical structures get very small — on the order of molecular or atomic sizes with one or more dimensions on the nanoscale — their behavior and interactions with energy, including...

Reading and writing systems for polygonal scanners differ in the use of the scanner. However, many performance characteristics are similar for both. In writing applications, a light source, usually a...

Lenses come in a variety of shapes, sizes and materials. They can be made of a single piece of glass or have multiple elements; their surfaces can be spherical, aspheric or cylindrical; they can be...

For any discussion of laser beam diagnostics, it is first necessary to define some terms that characterize beam properties. Broad definitions can include measurements of laser energy or power,...

Laser diodes vary widely in their wavelengths, powers, spectra and beam quality. Yet they share two fundamental components with all other lasers: an optical amplifier and a resonator that confines...