Photonics HandbookTechnology News

3D Printed Micro-optics Embed into a Durable Hybrid Laser

Facebook X LinkedIn Email
Researchers have shown that 3D-printed polymer-based micro-optics can withstand the heat and power levels that occur inside a laser. The advancement enables inexpensive compact and stable laser sources that would be useful in a variety of applications, including the lidar systems used for autonomous vehicles.

The researchers 3D-printed microscale optics directly onto optical fibers to combine fibers and laser crystals inside a single laser oscillator in a compact way. The resulting hybrid laser exhibited stable operation at output powers of over 20 mW at 1063.4 nm and had a maximum output power of 37 mW.

“We significantly reduced the size of a laser by using 3D printing to fabricate high-quality micro-optics directly on glass fibers used inside of lasers,” said research team leader Simon Angstenberger from the 4th Physics Institute at University of Stuttgart in Germany. “This is the first implementation of such 3D-printed optics in a real-world laser, highlighting their high damage threshold and stability.”
Researchers printed microscale lenses directly onto optical fibers, allowing them to compactly combine fibers and laser crystals inside a single laser oscillator. Courtesy of Moritz Floess and Simon Angstenberger, 4th Physics Institute at University of Stuttgart in Germany.
Researchers printed microscale lenses directly onto optical fibers, allowing them to compactly combine fibers and laser crystals inside a single laser oscillator. Courtesy of Moritz Floess and Simon Angstenberger/4th Physics Institute at University of Stuttgart in Germany.

The new laser combines the compactness, robustness, and low cost of fiber-based lasers with the advantages of crystal-based solid-state lasers, which can have a broad range of properties such as different powers and colors.

“Until now, 3D-printed optics have primarily been used for low-power applications such as endoscopy,” Angstenberger said. “The ability to use them with high-power applications could be useful for lithography and laser marking, for example. We showed that these 3D micro-optics printed onto fibers can be used to focus large amounts of light down to a single point, which could be useful for medical applications such as precisely destroying cancerous tissue.”

The team uses a 3D-printing approach known as two-photon polymerization, which focuses an infrared laser into a ultraviolet-sensitive photoresist. In the laser’s focal region, two infrared photons will be absorbed simultaneously, which hardens the UV resist. Moving the focus around allows various shapes to be created with high precision. This method use can be used to create miniaturized optics and also allows novel functionalities such as the creation of free-form optics or complex lens systems.

“Because these 3D-printed elements are made of polymers, it was unclear whether they could withstand the significant amount of heat load and optical power that occurs inside a laser cavity,” Angstenberger said. “We found that they are surprisingly stable, and we were not able to observe any kind of damage on the lenses even after several hours of running the laser.”

For the new study, the researchers used a 3D printer made by Nanoscribe to fabricate lenses with a 0.25-mm diameter and 80-µm height onto the end of a fiber with the same diameter using two-photon polymerization. This involved designing an optical element with commercial software, inserting the fiber into the 3D printer, and printing the small structure on the end of the fiber. This process must be extremely precise in terms of aligning the printing to the fiber and the accuracy of the printing itself.

After the printing was complete, the researchers assembled the laser and the laser cavity. Rather than using a crystal inside a laser cavity made of bulky and costly mirrors, they used fibers to form part of the cavity, creating a hybrid fiber-crystal laser. The lenses printed at the end of the fibers focus and collect — or couple — the light into and out of the laser crystal. They then glued the fibers into a mount to make the laser system more stable and less susceptible to air turbulence. The crystal and the printed lenses measured just 5 × 5 cm2.

Continuously recording the laser power over several hours verified that the printed optics inside the system did not deteriorate or affect the long-term properties of the laser. Additionally, scanning electron microscopy images of the optics after use in the laser cavity did not show any visible damage. “Interestingly, we found that the printed optics were more stable than the commercial fiber Bragg grating we used, which ended up limiting our maximum power,” Angstenberger said.

The researchers are now working to optimize the efficiency of the printed optics. Larger fibers with optimized freeform and aspherical lens designs or a combination of lenses printed directly onto the fiber could help improve the output power. They would also like to demonstrate different crystals in the laser, which could allow the output to be customized for specific applications.

The research was published in Optics Letters (

Published: December 2023
Polymers are large molecules composed of repeating structural units called monomers. These monomers are chemically bonded together to form long chains or networks, creating a macromolecular structure. The process of linking monomers together is known as polymerization. Polymers can be classified into several categories based on their structure, properties, and mode of synthesis. Some common types of polymers include: Synthetic polymers: These are human-made polymers produced through...
A lens is a transparent optical device that focuses or diverges light, allowing it to pass through and form an image. Lenses are commonly used in optical systems, such as cameras, telescopes, microscopes, eyeglasses, and other vision-correcting devices. They are typically made of glass or other transparent materials with specific optical properties. There are two primary types of lenses: Convex lens (converging lens): This type of lens is thicker at the center than at the edges....
Meta-optics, also known as metasurface optics or flat optics, is a branch of optics that involves the design, fabrication, and utilization of artificial structures called metasurfaces to control and manipulate light at the nanoscale level. Unlike traditional optics, which typically involve bulky lenses and mirrors, meta-optics aims to achieve similar functionalities using ultrathin, planar structures composed of subwavelength nanostructures. Metasurfaces are typically composed of arrays of...
Photoresist is a light-sensitive material used in photolithography processes, particularly in the fabrication of semiconductor devices, integrated circuits, and microelectromechanical systems (MEMS). It is a crucial component in the patterning of semiconductor wafers during the manufacturing process. The primary function of photoresist is to undergo a chemical or physical change when exposed to light, making it selectively soluble or insoluble in a subsequent development step. The general...
additive manufacturing
Additive manufacturing (AM), also known as 3D printing, is a manufacturing process that involves creating three-dimensional objects by adding material layer by layer. This is in contrast to traditional manufacturing methods, which often involve subtracting or forming materials to achieve the desired shape. In additive manufacturing, a digital model of the object is created using computer-aided design (CAD) software, and this digital model is then sliced into thin cross-sectional layers. The...
two-photon polymerization
Two-photon polymerization (TPP) is a technique used in additive manufacturing, specifically in the field of 3D printing. It involves using a focused laser to polymerize a photosensitive material in a precise and controlled manner. The process relies on the nonlinear absorption of photons, where two photons are absorbed simultaneously to initiate a chemical reaction that leads to polymerization. Here is a breakdown of the key components and steps involved: Photosensitive material: The...
optical fiber
Optical fiber is a thin, flexible, transparent strand or filament made of glass or plastic used for transmitting light signals over long distances with minimal loss of signal quality. It serves as a medium for conveying information in the form of light pulses, typically in the realm of telecommunications, networking, and data transmission. The core of an optical fiber is the central region through which light travels. It is surrounded by a cladding layer that has a lower refractive index than...
Research & TechnologyLasersOpticsfiberpolymerlensmeta-opticscrystalsoscillatorUVresistphotoresistadditive manufacturingtwo-photon polymerizationoptical fiber4th Physics InstituteUniversity of StuttgartGermanyEuropeOptics LettersTechnology News

We use cookies to improve user experience and analyze our website traffic as stated in our Privacy Policy. By using this website, you agree to the use of cookies unless you have disabled them.