Photonics Handbook

Diffraction gratings are optical components with a periodic structure that separate light into beams traveling in predictable directions based on their wavelength. The grating acts as the dispersive...

By its original definition, a nanopositioning device is a mechanism capable of repeatedly delivering motion in increments as small as one nanometer. Lately demands from industry and research have...

Optical fibers are made from either glass or plastic. Most are roughly the diameter of a human hair, and they may be many miles long. Light is transmitted along the center of the fiber from one end...

In their earliest forms, UV bandpass filters that were optimized for wavelengths less than 400 nm, such as the Schott UG or the Hoya U-series, were constructed of absorbing compounds in glass. Such...

The optical materials selected for an optical system depend upon the application, the required system performance and the environment in which the system is to perform; thus the materials’...

What are thin-film coatings? The purpose of any optical thin-film coating is to modify the transmittance and reflectance properties of the substrate material to which they are applied. Most coatings...

The use of precision polymer optics is becoming an increasing necessity today as products demand sophisticated light handling components to achieve desired results. Polymer optics can be thought of...

Controlling and minimizing heat output is desirable in most lighting applications. For example, conventional incandescent light sources are very inefficient with only a small portion of the...

All optical spectrometry techniques rely on the measurement of radiant power. The configuration of the instrument varies based on the measurement technique: absorption, emission, luminescence, or...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

Adhesives for fiber optic components that perform well on glass, metal, ceramic and most plastic substrates provide excellent chemical and solvent resistance. They also can act as an electrical...

Reflected-ultraviolet imaging is a rather mysterious area of the imaging field. There is relatively little actual UV imagery to be found on the Internet or in the literature compared to near-infrared...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

With a specific gravity of 1.85 g/cm3, beryllium is the lightest metal that is workable. It is 45 percent lighter than aluminum and approximately five times as stiff. Its stiffness to weight ratio...

Image intensification, the basis of night vision, is a complex conversion of energy particles that occurs within a vacuum tube. An image-intensifier system works by collecting photons through an...

The basic setup in laser perforation includes a pulsed laser, a lens and either a moving mirror, a rotating web or both. Each laser pulse creates a hole in the material. During the blank time in...

Charged-injection device imagers are metal-oxide semiconductor (MOS) detectors that can be fabricated using PMOS, NMOS and CMOS integrated circuit technology, and may be configured as a...

DATA TABLES: OPTICAL THIN-FILM MATERIALS Identification Physical Parameters Material Name Material Formula Transparent Region(µm) (see note a) Index at Wavelength...

Optics can be contaminated in many ways. Contamination can be kept to a minimum by returning the optics to their case after use or by covering the optics for protection from the outside environment....

The basic difference between the household mirror and the optical mirror is that one is coated on the back surface and the other is coated on the front. For optical applications, a front-surface...

Optics today needs alchemy, and the forces that motivate microchip technology are a key reason why. Today, light can transmit and process digital information as well as electricity can — in...

Plate beamsplitters Plate beamsplitters consist of a thin plate of optical crown glass with a different type of coating deposited on each side. The first surface is coated with an all-dielectric...

Lenses come in a variety of shapes, sizes and materials. They can be made of a single piece of glass or have multiple elements; their surfaces can be spherical, aspheric or cylindrical; they can be...

Imaging has long been used in industrial processes to measure, monitor, control, or otherwise manage the production of goods. The challenge to the process designer is to develop a tool that captures...