Photonics Handbook

Early fiber lasers were inefficient and limited to low powers, until more effective methods emerged to deliver the pump light into the cladding. Valentin Gapontsev, founder and CEO of IPG Photonics,...

Developed in the early 1990s, the silicon photomultiplier (SiPM) is a solid-state photodetector whose sensitivity to light rivals that of a photomultiplier tube (PMT) in a regime where a few hundred...

Silicon photonics is widely considered a key enabling technology for further development of optical interconnect solutions needed to address growing traffic on the internet. From the first submarine...

There are three fundamental properties of light: intensity, wavelength, and polarization. Almost all cameras today are designed for monochrome or color imaging. A monochrome camera is used to measure...

Materials processing with lasers is actually a broad term for a diverse range of applications. The major categories of these uses, and the lasers that service them, are summarized Table 1. At one...

By its original definition, a nanopositioning device is a mechanism capable of repeatedly delivering motion in increments as small as one nanometer. Lately demands from industry and research have...

Optical fibers are made from either glass or plastic. Most are roughly the diameter of a human hair, and they may be many miles long. Light is transmitted along the center of the fiber from one end...

Laser development for the microscopy market continues to be driven by key trends in applications, which currently include superresolution techniques, multiphoton applications in optogenetics and...

Any number of medical, industrial, and analytical applications requires the detection of light. Chemiluminescence, bioluminescence, fluorescence, and atomic absorption are just a few, and all require...

Over 60 years have passed since the first demonstration of a laser in 1960. After the initial spark of interest, lasers were for a while categorized as “a solution waiting for a problem,”...

The wavelength range of commercially available LEDs with single-element output power of at least 5 mW is 275 to 950 nm. Each wavelength range is made from a specific semiconductor material family,...

Neodymium-doped crystals and glasses such as Nd:YAG (neodymium:yttrium aluminum garnet) have long been used as laser gain materials. Optically pumped, they produce an output wavelength close to 1...

Images are produced by many means: cameras, x-ray machines, electron microscopes, radar and ultrasound. They are used in the entertainment, medical, scientific and business industries; for security...

Controlling and minimizing heat output is desirable in most lighting applications. For example, conventional incandescent light sources are very inefficient with only a small portion of the...

All optical spectrometry techniques rely on the measurement of radiant power. The configuration of the instrument varies based on the measurement technique: absorption, emission, luminescence, or...

Reflected-ultraviolet imaging is a rather mysterious area of the imaging field. There is relatively little actual UV imagery to be found on the Internet or in the literature compared to near-infrared...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

Photonics Rules of Thumb Scientists and engineers tend to want to answer simple relational questions with a blackboard covered with equations, even when questioners just want a rough estimate to...

Image intensification, the basis of night vision, is a complex conversion of energy particles that occurs within a vacuum tube. An image-intensifier system works by collecting photons through an...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

High-brightness LEDs have found their way into applications such as signs and displays, cell phone flash modules, automotive lighting and general illumination. Some applications, however, such as...

Optics today needs alchemy, and the forces that motivate microchip technology are a key reason why. Today, light can transmit and process digital information as well as electricity can — in...

When physical structures get very small — on the order of molecular or atomic sizes with one or more dimensions on the nanoscale — their behavior and interactions with energy, including...

Laser diodes vary widely in their wavelengths, powers, spectra and beam quality. Yet they share two fundamental components with all other lasers: an optical amplifier and a resonator that confines...

Unlike an edge emitter, a VCSEL has a maximum operating power that is not limited by catastrophic optical damage of the exit aperture because its aperture is larger and its PN junction does not...

The applications where rapid detection of light is a must are many. They include a wide variety: semiconductor inspection, gene sequencing, oil well logging and high-energy physics. The reasons for...

The scope of optical spectroscopic instrumentation is indeed very broad. Many analytical methods rely on the interaction of radiation with matter and are often described in the context of quantum and...