Photonics Handbook

Diffraction gratings are optical components with a periodic structure that separate light into beams traveling in predictable directions based on their wavelength. The grating acts as the dispersive...

Early fiber lasers were inefficient and limited to low powers, until more effective methods emerged to deliver the pump light into the cladding. Valentin Gapontsev, founder and CEO of IPG Photonics,...

Developed in the early 1990s, the silicon photomultiplier (SiPM) is a solid-state photodetector whose sensitivity to light rivals that of a photomultiplier tube (PMT) in a regime where a few hundred...

Electrical engineers are very familiar with the effects of shot noise, thermal noise, flicker noise and crosstalk, and recognize how these effects can reduce the signal-to-noise ratio (SNR) in their...

Silicon photonics is widely considered a key enabling technology for further development of optical interconnect solutions needed to address growing traffic on the internet. From the first submarine...

Superresolution optical microscopy, for which the Nobel Prize was awarded to Eric Betzig, Stefan Hell, and William Moerner in 2014, has been one of the most momentous developments in the life...

There are three fundamental properties of light: intensity, wavelength, and polarization. Almost all cameras today are designed for monochrome or color imaging. A monochrome camera is used to measure...

Technological advances have resulted in new, higher-quality sensors that enable machine vision cameras to deliver greater features and functionality at a lower cost than ever before. These factors...

Materials processing with lasers is actually a broad term for a diverse range of applications. The major categories of these uses, and the lasers that service them, are summarized Table 1. At one...

Since its first successful operation in 1960 at Hughes Research Labs, the laser technology has been at the center of innovation and research. Semiconductor lasers first made their appearance in 1962...

Many common spectroscopic measurements require the coordinated operation of a detection instrument and light source, as well as data acquisition and processing. Integration of individual components...

When evaluating the surface of a component, surface roughness can be assessed by eye or by rubbing it with a fingertip. Common expressions include “shiny,” “lusterless and...

By its original definition, a nanopositioning device is a mechanism capable of repeatedly delivering motion in increments as small as one nanometer. Lately demands from industry and research have...

Optical fibers are made from either glass or plastic. Most are roughly the diameter of a human hair, and they may be many miles long. Light is transmitted along the center of the fiber from one end...

Light is a versatile tool for investigating physical and chemical processes in nature. Any specific system being analyzed may, through the light it emits or reflects, communicate information about...

Flat optics generally perform three main functions: They transmit light (windows), reflect light (mirrors), and fold light (prisms). While most optical manufacturers make spherical and flat optics, a...

When purchasing an industrial laser system, the astute buyer will look for a Class 1 laser product — a system where the laser beam hazard is completely enclosed and there is no potential laser...

Optical design software allows the user to develop a configuration of optical elements that manipulate the trajectory of light for the purposes of creating an image, illuminating a target, coupling...

As you operate your laser, only a portion of the electrical power sourced from your laser driver converts to light energy. The remainder turns to heat, and the buildup of that thermal energy presents...

Laser development for the microscopy market continues to be driven by key trends in applications, which currently include superresolution techniques, multiphoton applications in optogenetics and...

Single-crystal sapphire has been the material of choice for defense and other applications that require extremely durable optics, but aluminum oxynitride (ALON) and magnesium aluminate (spinel) have...

Any number of medical, industrial, and analytical applications requires the detection of light. Chemiluminescence, bioluminescence, fluorescence, and atomic absorption are just a few, and all require...

The use of precision polymer optics is becoming an increasing necessity today as products demand sophisticated light handling components to achieve desired results. Polymer optics can be thought of...

Neodymium-doped crystals and glasses such as Nd:YAG (neodymium:yttrium aluminum garnet) have long been used as laser gain materials. Optically pumped, they produce an output wavelength close to 1...

In their earliest forms, UV bandpass filters that were optimized for wavelengths less than 400 nm, such as the Schott UG or the Hoya U-series, were constructed of absorbing compounds in glass. Such...

What are thin-film coatings? The purpose of any optical thin-film coating is to modify the transmittance and reflectance properties of the substrate material to which they are applied. Most coatings...

The first high-reflectance mirror coatings for the UV and vacuum UV (VUV) were of the Al + MgF2 type produced in the late 1950s. Coatings of this design are still used today for multigas cavity...

Over 60 years have passed since the first demonstration of a laser in 1960. After the initial spark of interest, lasers were for a while categorized as “a solution waiting for a problem,”...

An integrating sphere’s function is to spatially integrate radiant flux (light). However, before one can optimize a sphere design for a particular application, it is important to understand how...

In general, there are three common approaches to reducing mechanical excitation of photonic systems. The first is identifying the sources of vibration and implementing ways to eliminate or reduce...

The wavelength range of commercially available LEDs with single-element output power of at least 5 mW is 275 to 950 nm. Each wavelength range is made from a specific semiconductor material family,...

One of the most critical elements of any time-resolved spectroscopy and dynamics experiment is the optical delay line. A typical optical delay line consists of a retroreflector or folding mirrors on...

Since their invention in the late 1960s, charge-coupled devices, also called CCDs, have found widespread use in imaging applications. Electronic cameras based on CCD technology are used in...

Image intensification, the basis of night vision, is a complex conversion of energy particles that occurs within a vacuum tube. An image-intensifier system works by collecting photons through an...

Charged-injection device imagers are metal-oxide semiconductor (MOS) detectors that can be fabricated using PMOS, NMOS and CMOS integrated circuit technology, and may be configured as a...

Adhesives for fiber optic components that perform well on glass, metal, ceramic and most plastic substrates provide excellent chemical and solvent resistance. They also can act as an electrical...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

An optical time-domain reflectometer sends short pulses of light into a fiber and measures its reflections as a function of time. The delay of these reflections to the detector as well as their...

The common polycrystalline materials used for optical thin-film materials do not satisfy the requirements of telecommunications because of the instabilities caused by moisture absorption in their...

Reflected-ultraviolet imaging is a rather mysterious area of the imaging field. There is relatively little actual UV imagery to be found on the Internet or in the literature compared to near-infrared...

The ubiquitous Nd:YAG laser has played many roles over the years. For the military, it has provided rangefinding and target designation capabilities. When used with nonlinear optics or as a pump...

Measuring pulsed-beam lasers has generally required the use of a CCD array profiler. This is a reasonable solution for low-power lasers in the UV and visible wavelength range, but these require...

To the novice or casual user of optics, the acquisition of an optical system can be a very difficult experience. Failure to understand the ground rules can result in unnecessarily high cost, late...

If we were to estimate the output of a CCD or thermal camera, we would typically draw an image over the detectors, aligning the image with the detector axes. We show it this way because it’s...

While some design engineers know exactly what they need from their laser diode, others may choose a partner to navigate what can be a complex development process. Laser diode manufacturers know which...

Manufacturing the laser diode is complicated by the existence of multiple proprietary techniques and intellectual property barriers together with complex device physics and unique materials. ...

That portion of the spectrum that the eye can see — and its rainbow of colors — is rather small, covering approximately 360 to 830 nm. What colors we perceive depends on wavelength, while...

Hyperspectral imaging spectroscopy has developed dramatically from a large, complex, remote-sensing satellite- or aircraft-based system into a rugged, compact, economically priced imaging and...

Illumination design has developed rapidly to include not only automotive headlamps and street lamps, but also backlit displays, fluorescent panel lighting, light-emitting diode or laser sources, and...

Intensity and uniformity can be described using different physical attributes, which makes interpreting requirements somewhat confusing. This article intends to provide an explanation and serve as a...